 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| td1600alf-4 tuner module for digital terrestrial (ofdm) applications rev.c ? 23-04-2007 preliminary data sheet 1. general description td1600alf-4 belong to the new generation of terrestrial tuners designed to cope with digital cofdm and analog transmission standards. from function point-of-view these tuners can be divided into two high-frequency sections, a rf-loopthrough and a single conversion tuner part. in the loopthrough section broadband low-no ise amplifiers are used. the loopthrough frequency response covers the entire frequency range from vhf to uhf. the rf-downstream section is equipped with a state-of-the-art single conversion tuner, which makes use of a highly integrated mopll ic that provides the required high level of performance necessary for cofdm signal processing. the tuners are provided with a dc/dc converter to generate the tuning voltage internally. the internal 4mhz pll crystal reference frequency is fed through one of the pin- terminals and can be used as a clock for a 2 nd device e.g. the channel decoder. two if-outputs are provided, one is a wideband, non filtered if-output, while the other, narrow-band if-output is equipped with a sa w-filter and a gain controllable if-amplifier. this narrow-if-output matches the a-to-d conv erter input of currently available channel decoders. all tuners out of this family can be equipped with two standard iec-connectors, rf-in is iec-female, rf-out is iec-male. the tuner housing is available in a vertical or horizontal mountable execution; the pinning pitch corresponds to the world standard pinning convention. apart from the rf-connectors, all other terminals are made with wire pins at the bottom side of the tuner.
nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 2 of 27 table 1. frequency allocation table parameter td1611alf-4/ td1311alf-4 TD1344ALF-4 174 mhz ? 230 mhz rf frequency range 474 mhz ? 858 mhz (*) 474 mhz ? 858 mhz (*) channel bandwidth 7/8mhz 8 mhz rf-loopthrough range ch e2 - ch e69 ch e2 - ch e69 if-center frequency 36.16 mhz 36.16 mhz rf input connector iec female iec female rf output connector iec male iec male ( * ) data refer to rf-channel center frequency. 2. features ? highly integrated rf-module, 3-band tuner plus active loopthrough ? +5v supply voltage only; no external tuning voltage required ? tuners for horizontal and vertical mounting available ? option with dc ? power output through input connector (e.g. indoor antenna supply) ? tuners comply with relevant cenelec standards with regard to requirements concerning signal handling capability and immunity ? superior low noise and high sensitivity performance ? rf-in to rf-out loopthrough amplifiers ? low noise and excellent linearity ? full vhf to uhf frequency range coverage ? standard connectors for in- and output e.g. iec, f-connector, rca ? high performance and cost effect ive single conversion tuner ? i2c programmable ? 400khz bus compliant ? fast pll tuning speed (programmable st ep size e.g. 62.5khz and 166.67khz) ? tuner internal gain control loop with selectable takeoverpoint settings via i2c bus ? external gain control possible with internal loop disabled ? 4.0v (max. gain) to 0v (min. gain) gain control voltage ? flat overall frequency response ? high pll loop bandwidth which ensures very low oscillator phase noise ? 4 mhz crystal reference frequency output ? saw-filter and if-amplifier included ? switchable 7/8 mhz saw filter ? fixed 8 mhz saw filter ? if-amplification controllable over a wide range nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 3 of 27 ? differential, filtered (saw) ?digital? if-out put to directly drive the channel decoder 3. ordering information table 2. ordering information table description (optional) package type number name description version td1611alf/ivp-4 3112 297 15531 vhf 3 ? uhf pll tuner, loopthrough, antenna power, screw hole, dc/dc converter, iec connector, vertical mount - td1611alf/ihp-4 3112 297 15521 vhf 3 ? uhf pll tuner, loopthrough, antenna power, screw hole, dc/dc converter, iec connector, horizontal mount - td1311alf/ivp-4 3112 297 15491 vhf 3 ? uhf pll tuner, loopthrough, antenna power, dc/dc converter, iec connector, vertical mount - td1311alf/ihp-4 3112 297 15481 vhf 3 ? uhf pll tuner, loopthrough, antenna power, dc/dc converter, iec connector, horizontal mount - td1644alf/ivp-4 3112 297 15631 uhf only pll tuner, loopthrough, antenna power, screw hole, dc/dc converter, iec connector, vertical mount - td1644alf/ihp-4 3112 297 15621 uhf only pll tuner, loopthrough, antenna power, screw hole, dc/dc converter, iec connector, horizontal mount - td1344alf/ivp -4 3112 297 15511 uhf only pll tuner, loopthrough, antenna power, dc/dc converter, iec connector, vertical mount - td1344alf/ihp-4 3112 297 15501 uhf only pll tuner, loopthrough, antenna power, dc/dc converter, iec connector, horizontal mount - td1311af/php-4 3112 297 15691 vhf 3 ? uhf pll tuner, antenna power, dc/dc converter, phono connector, horizontal mount - nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 4 of 27 4. block diagram rf-input rf- o utput dc-power for indoor antenna (1) saw high-band mid-band low-band osc. osc. osc. 33v v 5v tune high mid low agc +5v tuner supply voltage . mopll pll ic-bus 2 agc loop agc loop 4mhz crystal reference if - output (broadband) if - agc if - output (narrowband) reference frequency output (6) (2) ( 7) (4/5) (9) (8) (10/11) fig 1. block diagram of td1616alf nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 5 of 27 5. pinning information 5.1 pinning fig 2. pinning diagram 5.2 pin description table 3. pin description table description (optional) pin description 1 dc-power option for tuners with p-extension [1] 2 external rf-gain control voltage (0.5v - 4.0v) [2] 3 pll chip address select (i 2 c / tuner) [3] 4 scl (i 2 c / tuner) 5 sda (i 2 c / tuner) 6 4mhz reference frequency output [4] 7 +5v 5% supply tuner (v tu ) 8 'broadband' if ? output [4] 9 if-gain control voltage [5] 10 'narrowband' if ? output 1 [4] 11 'narrowband' if ? output 2 [4] [1] max. permissible current: 35ma [2] max. permissible control voltage source impedance limited to 200ohms (see application notes) [3] see application notes [4] ac coupled [5] max. gain at 3v,min. gain at 0v (see application notes) nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 6 of 27 6. limiting values table 4. limiting values under non-operational conditions table description (optional) symbol parameter conditions min max unit t amb ambient temperature -25 +85 c rh relative humidity - 95 % g b bump acceleration 25g - 245 m/s 2 g s shock acceleration 50g - 490 m/s 2 a vib vibration amplitude 10hz to-55 hz - 0.35 mm 7. static characteristics table 5. static characteristics t amb = -10 c to +60 c, rh=95 symbol parameter conditions min typ max unit v l dc-loopthrough to input connector optional - - 20 v i l max. permissible current - - 35 ma v tu tuner supply volt age 4.75 5.00 5.25 v i tu relevant supply current 180 200 210 ma v agc tuner agc input voltage - 4.0 4.5 v ? v agc agc input voltage range 0.3 - 4.0 v i agc agc control current at 0v agc voltage -2 - - ma v if-agc if- agc input voltage - 3.0 4.0 v ? vif-agc if- agc input voltage range 0 - 3.5 v i if-agc if- agc input current - - 10 a v as address select input voltage - - 5.25 v v scl serial clock input voltage -0.3 - 5.25 v v sda serial data input voltage -0.3 - 5.25 v i sda serial data input current -1 - 5 ma nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 7 of 27 8. dynamic characteristics next specification data refer to the overall performance from rf-i nput to if-output. if not otherwise stated, all data are assigned to broadband if-output. the tuner has to be tuned as such that co incidence between rf-channel center and if- center frequency of 36.16 mhz is given. table 6. dynamic characteristics t amb = 22 c 2 c; rh =60%10%; v tu =5v0.1v; v rf_agc =4.0v0.1v(internal agc detector disabled):v if_agc =1v(maximum); z i(rf) = 75 ? ; z o(rf) =75 ? ; unless otherwise stated. parameter conditions min typ max unit td1611 (vhf high) 174 230 mhz td1611 (uhf) 470 862 mhz frequency ranges (1) td1644 (uhf) 470 862 mhz rf power gain (2) 47 50 db overall gain taper 6 db low band 40 db mid band 40 db rf agc range high band 35 db vhf high (mid band) 66 70 db image rejection (referred to if-center frequency) uhf (high band) 55 60 db osc. voltage at aerial input (f < 1000mhz) <20 dbv in-channel return loss (3) 5 7 db overloading causing 1db gain compression 76 dbv noise figure at nom. gain 5 6 db esd protection of terminals 2 kv surge protection at rf-input 5 kv at 1 khz -88 -78 dbc/hz osc. phase noise (4) at 10 khz -90 -82 dbc/hz overall voltage gain (5 70 db [1] channel center including tuning margin [2] to be measured at ?broadband? if-output with 75ohms load [3] to be measured at rf-input in the range channel-center 3mhz [4] pll step size 166.667khz / 148.86khz; cp as recommended (see application notes) [5] measured at terminals 10/11; if-agc voltage (terminal 9) set to 3v nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 8 of 27 cross-modulation: definition: the cross-modulation is defined as the transfer of the adjacent channels' modulation depth to the wanted carrier. measurement: unwanted carriers (f unw ) = wanted carrier (f w ) 8mhz level of all carriers = 70dbv modulation = am, 50%, 15khz if-output loaded with 1k ? // 15pf // 1.2uh (load compensation) if-output level limited to 104dbv spec. limit: max. cross-modulation is less or equal 1% (typ. 0.3%) flatness (tilt) of overall responds curve (to be measured at broad-band if-output): definition: tilt of curve is defined in the specified if-range from highest to lowest gain point at nom. gain measured at broadband if-output: ? in the range if-center 3mhz : 3db max. ? in the range if-center 4mhz : 4db max. deterioration of flatness during agc (0db to 30db): 1.0db max. +6 +2 0 -2 -4 -6 +4 -4 -3.0 +3.0 +4 36.00 mhz db . . . . fig 3. flatness (tilt) of overall responds curve nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 9 of 27 a. 7mhz wide saw-filter selected b. 8mhz wide saw-filter selected fig 4. typical response curves at narrowband if-output 8.1 input sensitivity: the typical input sensitivity, when measur ed in an adequate application (i.e. philips semiconductors cofdm reference board om5754) is: - 82dbm , ber 2x10 - 4 post viterbi conditions: gaussian channel w/o added noise, 8k ofdm, 64qam, code rate 2/3, guard interval 1/8 8.2 4mhz reference output (terminal 6): frequency accuracy : 80ppm max. max. permissible load : t.b.f. output level : 440mvpp typ. [ 0 c - 60 c ; supply voltage (terminal 7) +5v5% ; loaded with min. t.b.d. ] phase noise @ 1khz : -104dbc/hz typ. center 36.13mhz center 36.13mhz 1.5mhz/ 1.5mhz/ span 15mhz span 15mhz 10db/ 10db/ . . . . nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 10 of 27 8.3 overall performance from rf input to rf output table 7. overall performance from rf input to rf output specification data refer to the overall performance from rf-input to rf-output. (valid for all tuners out of this family) parameter min typ max unit frequency range (referred to channel center) 51 858 mhz power gain 0 3 db overall gain taper 2.5 db noise figure (tuners w/o remod) 5 db cso / ctb (acc. en50083) -57 dbc rf-output return loss (referred to 75 ? ) 10 db 9. application information 9.1 programming of tuner pll the tuner control (frequency selection and band switching) is done via the i 2 c bus. one address byte and four data bytes are needed to fully program the tuner. a pll lock flag can be read from the tuner during 'read' - mode. four independent pll addresses are available; which one is actually valid depends on the address select voltage that is connected to terminal 3. td1300alf tuners comply to the 5v i 2 c ? bus specification. table 8. -bus data format ' write ' - mode: name description 7 6 5 4 3 2 1 0 ack adb address byte 1 1 0 0 0 ca1 ca0 r/w=0 a div1 divider byte1 0 n14 n13 n12 n11 n10 n9 n8 a div2 divider byte2 n7 n6 n5 n4 n3 n2 n1 n0 a 1 d/a=1 0 0 1 r2 r1 r0 a cb1 control data byte1 1 d/a=0 0 0 atc al2 al1 al0 a cb2 control data byte2 cp2 cp1 cp0 sp5 sp4 sp3 sp2 sp1 a nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 11 of 27 table 9. description of used symbols symbol description conditions ca1, ca0 chip address selection bits [1] r/w read/write bit bit = 0 (write mode), bit = 1 (read mode) n14 to n0 lo frequency divider bits - d/a = 1 ? following 6 bits contain test and reference divider ratio data d/a d/a = 0 ? following 6 bits contain agc setting data r2, r1, r0 reference divider bits [2] sp5 ..... sp1 band selection and saw filter switch ports atc = 1 ? enables fast tuning speed during channel search mode atc agc time constant data bit; only valid with int. agc loop active atc = 0 ? recommended after channel acquisition; normal mode al2, al1, al0 agc take-over-point bits [3] cp2, cp1, cp0 pll charge pump current selection bits [4] bit = 1 ? port v out is 'on? sp5 - sp1 switch ports [5] bit = 0 ? port v out is 'off ca1, ca0 programmable address selection bits [6] [1] see table: programmable address selection [2] see table: reference divider settings [3] see table: internal agc loop top [4] see table: charge pump settings [5] see table: band and saw-filter selection table table 10. programmable address selection bits (ca1, ca0) ca1 ca0 voltage applied to terminal 3 0 0 0v to 0.1x vtu 0 1 terminal open 1 0 0.4xvtu to 0.6xvtu 1 1 0.9xvtu to 1.0xvtu nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 12 of 27 n14 to n0: programmable divider bits divider ratio: n = n14x2 14 + n13x2 13 + ... + n1x2 1 + n0 how to calculate the divider ratio n : ( ) ? ? ? ? ? ? + = hz hz f f f n ref if input whereby [] khz hz f ref 5 . 62 64 10 4 ) 1 ( 6 = ? = [] khz hz f ref 67 . 166 24 10 4 ) 1 ( 6 = ? = note (1) : divider ratio to be set with bits ' r2 ..... r0 ' (see table below) do not set the divider ratio as such that the t uner is tuned into extreme conditions i.e. far below or far above the specified ranges. r2, r1, r1: pll reference divider settings ( control data byte 1): important note: in order to avoid instabilities of t he reference divider it is advisable to set the reference divider in combination wi th the if-frequency and channel spacing as per below table table 11. pll reference divider settings (control data byte) pll step size (khz) pll ref. divider ratio r2 r1 r0 if frequency (mhz) channel spacing (mhz) 142.86 28 0 0 1 36.16 8 166.67 24 0 1 0 36.16 6 and 7 al2, al1, al0: agc take-over-point bits ( control data byte 1 ): external agc mode: the tuner can be controlled by an external gain control voltage applied to terminal 2 of the tuner. in that case the alx - bits need to be set as shown in table below. the impedance of the control voltage source should not exceed 200ohms. [] khz hz f ref 86 . 142 28 10 4 ) 1 ( 6 = ? = nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 13 of 27 table 12. external agc mode setting al2 al1 al0 typical top level remarks 0 0 0 124dbuv 0 0 1 121dbuv - 0 1 0 118dbuv - 0 1 1 115dbuv - 1 0 0 112dbuv - 1 0 1 109dbuv - 1 1 0 i agc = 0 external agc (1) 1 1 1 v agc = 3.5v loop disabled (2) [1] the tuner internal agc current sources are disabled (default mode after power on reset). [2] the tuner internal agc detector is disabled. with no external agc voltage applied to the tuner, the rf- gain is always set to maximum. cp2, cp1, cp0: pll charge pump current settings note: during search tuning it is recomm ended to set the pll to a moderate charge pump. to enable best oscillator phase noise perfor mance during digital signal processing, the pll charge pump current should be set to co nditions as given with following table. table 13. pll charge pump current settings cp2 cp1 cp0 typical cp current (ua) recommendations 0 0 0 40 - 0 0 1 60 - 0 1 0 90 to be used during search tuning and for 50khz, 62.5khz pll step sizes low band: 87mhz to 130mhz mid band: 200mhz to 290mhz 0 1 1 130 high band: 480mhz to 620mhz 1 0 0 190 - low band: 130mhz to 160mhz mid band: 290mhz to 420mhz 1 0 1 280 high band: 620mhz to 830mhz low band: 130mhz to 160mhz 1 0 1 280 mid band: 290mhz to 420mhz nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 14 of 27 low band: >160mhz(*) 1 1 0 410 mid band: >420mhz(*) 1 1 1 600 high band: >830mhz (*) (*) oscillator frequencies table 14. sp5 ??sp1 band and saw-filter selection table band sp5 sp4 sp3 sp2 sp1 low ? band 0 x 0 0 0 mid ? band 0 x 0 1 0 high ? band 0 x 1 0 0 7 mhz saw filter 0 0 x x x 8 mhz saw filter 0 1 x x x table 15. i 2 c-bus data format, ' read ' - mode description 7 6 5 4 3 2 1 0 ack address byte 1 1 0 0 0 ca1 ca0 r/w=1 a status byte por fl 0 1 agc 1 0 0 a a : acknowledge ca1 / ca0 = chip address (see address selection table) por= power-on-reset-flag ; por = 1 after power-on fl= in-lock-flag ; fl = 1 when pll is phase locked agc= internal agc flag ; agc = 1 when internal agc is active nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 15 of 27 timing of program sequences: because of the tuner ? pll frequency divider settling time of min. 60usec. , the occurrence of any other i2c traffic start cond ition present within that periode on the bus will disturb the divider and result in a not properly tuned tuner vco. each time the tuner-pll frequency divider has been pr ogrammed, a 60usec wait becomes necessary before continuing the i2c bus traffic. fig 5. program sequence 9.2 max. permissible if-load impedance: the max. load applied to the ' broadband ' if-output of the tuner should not exceed: 2k ? min.//15pf max. the reactive load has to be compensated (tuned-out to the if-center frequency) by an inductance connected in parallel to the load. the max. load applied to the ' narrowband ' balanced if-output of the tuner is limited to 1k ? min. tuner pll-chip address modulator-pll address tuner pll-chip address tuner pll-chip address any other iic device start start start start start stop stop stop stop stop divider byte 1 divider byte 1 data date byte 1 date byte 1 date byte 1 divider byte 1 data divider byte 2 divider byte 2 data data byte 2 data byte 2 data byte 2 divider byte 2 data 60 usec 60 usec . . . . nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 16 of 27 -90.0 -80.0 -70.0 -60.0 -50.0 -40.0 -30.0 -20.0 -10.0 0.0 3.50 3.25 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0.00 gain control voltage at terminal 9 [v] gain reduction [db] 9.3 gain control characteristics of if amplifier fig 6. gain control characterist ic of if-amplifier (terminal 9) (1) with an if-gain control voltage of about 1.3v applied to terminal 9 of tuner, the narrowband if-output level is about the same of the broadband if-output. fig 7. internal agc circuit 1 k v d 3 3 0 r 1 n f i f - a m p l i f i e r t e r m i n a l 9 . . . . nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 17 of 27 5v agc control voltage agc pin 2 td1600al 1k 100r 1.2k i <15ua agc . . . . f note: in case the above recommended agc control voltage source is not used, alternatively a control voltage source with a max. 200ohms impedance can be used fig 8. external rf-gain control voltage; recommended schematic 9.4 phase noise, i 2 c bus traffic and crosstalk the low noise pll used in these tuners w ill clean up the noise spectrum of the vcos close to the carrier to reach noise levels @ 1 khz offset from the carrier compatible with e.g. ofdm reception. linked to this noise improvement, some disturbances may become visible while they were not visible because they were hidden into the noise in analog dedicated applications and circuits. this is especially true for disturbances coming from the i 2 c bus traffic, whatever this traffic is intended for the mopll or for another slave on the bus. to avoid this i 2 c bus crosstalk and be able to have a clean noise spectrum, it is necessary to use a bus gate that enables the si gnal on the bus to drive the mopll. this is used only when the communication is intend ed for the tuner part (such a kind of i 2 c bus gate is included into the philips te rrestrial channel decoders), and to avoid unnecessary repeated sending of the same information. 9.5 main board recommendations: the tracks on the main board connected to t he tuners' terminals should be kept as short as possible in order to avoid interferences be cause of immunity problems and/or to avoid problems with regard to radiat ion of the local oscillator. nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 18 of 27 9.6 for tuners with antenna-power function (tuners with type name extension ?p?) attention: modules with type name extension 'p' do hav e the dc-supply option through out the rf- input connector on board. the max. permissibl e current drive has to be limited to 35ma . should this option be used in the end applicat ion, it is recommended that an electronic switch with some current protection circuitr y be employed, to avoid damage to the tuner itself. nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 19 of 27 10. package outline (1) fig 9. package outline of td1600alf-4 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 20 of 27 fig 10. package outline of td1600alf-4 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 21 of 27 fig 11. package outline of td1300alf-4 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 22 of 27 fig 12. package outline of td1300alf-4 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 23 of 27 11. packing information the products are packed in the carton box and transferred to customers by pallet transport. w b h carton boxes are made of corrugated fibre board which are free of environmentally banned substances. fig 13. example of carton box table 16. package information table description (optional) package dimension l x w x h (cm) number of sets gross weight (kg) carton vertical 46 x 34 x 7.5 98 4.09 pallet vertical 120 x 105 x 105 7742 345.1 carton horizontal 46 x 34 x 9.4 60 3.16 pallet horizontal 120 x 105 x 105 3900 227.4 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 24 of 27 12. mounting (1) fig 14. punching pattern of chassis pcb nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 25 of 27 13. revision history table 17. revision history table description (optional) document id release date data sheet status change notice supersedes td1600alf-4 2007-01-19 objective data sheet rev a- - modifications - td1600alf-4 2007-03-23 preliminary data sheet rev b rev a modifications ? mechanical drawings updated to nxp cover ? packaging information updated ? supply voltage and performance data updated ? change status to preliminary ? td1644alf/ivp-4 and td1644alf/ihp-4 added pg 2 - add product 12nc td1600alf-4 2007-04-23 preliminary data sheet rev c rev b modifications ? new type td1311af/php-4 added in page 3 nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications td1600alf-4 ? nxp b.v. 2006. all rights reserved. preliminary data sheet rev.c ? 23-04-2007 26 of 27 14. legal information 14.1 data sheet status document status [1][2] product status [3] definition objective [short] data sheet preliminary [short] data sheet product [short] data sheet development qualification production this document contains data from the objec tive specification for product development. this document contains data from the preliminary specification this document contains the product specification [1] please consult the most recently issued docum ent before initiating or completing a design. [2] the term ?short data sheet? is ex plained in section ?definitions?. [3] the product status of device(s) described in this docum ent may have changed since this document was published and may diffe r in case of multiple devices. the latest product status information is available on the internet at url http://www.nxp.com . 14.2 definitions draft ? the document is a draft version only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. 14.3 disclaimers general ? information in this document is believed to be accurate and reliable. however, nxp semiconductor s does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product de scriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? nxp semiconductors produ cts are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a nxp semiconductor s product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors accepts no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is for the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purposes only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. 14.4 licenses purchase of nxp nxp semiconductors td1600alf-4 tuner module for digital terrestrial (ofdm) applications please be aware that important notices concerning this document and the product(s) described herein, have been included in the section ?legal information?. ? nxp b.v. 2006. all rights reserved. for more information, please visit: http://www.nxp.com. for sales office addresses, email to: salesaddresses@nxp.com. date of release: 23-04-2007 document identifier: td1600alf-4 16. contents 1. general description.............................................1 2. featur es ...............................................................2 3. ordering information ..........................................3 4. block diag ram......................................................4 5. pinning information ............................................5 5.1 pinning ..................................................................5 5.2 pin descrip tion.......................................................5 6. limiting values ....................................................6 7. static charac teristics..........................................6 8. dynamic charact eristics ....................................7 8.1 input sensit ivity:.....................................................9 8.2 4mhz reference output (terminal 6):......................9 8.3 overall performance from rf input to rf output.10 9. application in formati on ....................................10 9.1 programming of tuner pl l ..................................10 9.2 max. permissible if -load imp edance: .................15 9.3 gain control characterist ics of if amplifier ..........16 9.4 phase noise, i 2 c bus traffic an d crosst alk ...........17 9.5 main board reco mmendations: ............................17 9.6 for tuners with antenna-power function (tuners with type name ex tension ?p?)..........................18 10. package out line .................................................19 11. packing inform ation..........................................23 12. mounting ............................................................24 13. revision hi story ................................................25 14. legal info rmation ..............................................26 14.1 data sheet status ................................................26 14.2 definiti ons............................................................26 14.3 disclaime rs..........................................................26 14.4 licens es ..............................................................26 14.5 patent s ................................................................26 14.6 trademar ks .........................................................26 15. contact info rmation ..........................................26 16. contents.............................................................27 |
Price & Availability of TD1344ALF-4
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |